5G Diplexer & Duplexer

Based on over 25 years of experience, Temwell is the leading 5G diplexer duplexer manufacturer in Taiwan. Our group provides One-stop service for Diplexer Duplexer, including 5G Duplexers, 5G Diplexers, VHF UHF Duplexers, VHF UHF Diplexers, TETRA Cavity Duplexer, Helix Cavity Diplexer, LTE Low PIM Diplexer, and Coaxial Duplexer. 

Our customer service covers frequency change, isolation requests, and power requests as below.

  • Frequency band: DC to 60GHz
  • Isolation: up to 60dB+
  • Power: 100W+

If you have any questions regarding our 5G duplexer duplexer products, welcome to contact us anytime!

Diplexer Duplexer Design
VHF UHF / 5G Diplexer and Duplexers Series
TETRA Cavity Duplexer Helix Cavity Diplexer LTE800 & GSM900 Low PIM Diplexer GSM1800 & UMTS & GSM900 Diplexer and Duplexer 5.8G Coaxial Duplexer Mobile Radio Quadriplexer
What is the Function of Temwell VHF UHF / 5G Diplexer & Duplexer Products?

Both Diplexer and Duplexer can be taken as "Duplexers", "5G Duplexers",  "5G Diplexers" or "VHF UHF Duplexers" which are extremely common radio frequency components in transmitter circuits, receiver circuits, and transceiver circuits used in communications, Radar, and other sensing applications under VHF UHF Band. Both VHF UHF Diplexer and VHF UHF Duplexer are three-port RF components, which use the frequency division function of high-pass, low-pass, or band-pass to run two signals of receiving and sending simultaneously under the same antenna or transmission line function.

Simply, the function of VHF UHF Diplexer & Duplexer is used to process 2 signal frequency bands which are from VHF to UHF at the same time, mainly based on the frequency band that the terminal device wants to operate. Except for 2 specific frequency bands, the other parts are treated as noise, which is isolated and removed. Usually, VHF UHF Diplexer & Duplexer is directly connected to the antenna terminal, and the signal collected by the antenna terminal is processed, and then respectively guided to the corresponding equipment.

As long as the VHF UHF Diplexer & Duplexer can fully separate the 2 signal frequency bands, and when it operates 2 frequency bands, these signals do not interfere with each other; it is the standard VHF UHF Duplexers. Common band combinations are 3: (1). 2 VHF BAND (2). 2 UHF BAND (3). 1 VHF BAND+1 UHF BAND. For VHF UHF Diplexer & Duplexer design, the difficulty is that when the two selected frequency bands are too close, it is easy to cause interference between the two signals. When the two internal frequency bands easily interfere with each other, VHF UHF Diplexer & Duplexer lose their operational significance. 

The key difference between VHF UHF Diplexer and VHF UHF Duplexer is the way the loop operates. VHF UHF Duplexer is based on two Bandpass filters, which protect the frequency bands that the terminal equipment will operate separately. In addition to better isolation between the two operating frequency bands, it can also fully isolate the noise outside the two frequency bands.  The disadvantage is that it requires high technical skills and it is difficult to meet all development requirements.

On the other side, VHF UHF Diplexer uses 1 lowpass filter and 1 highpass filter to achieve the purpose of protecting 2 operating frequency bands. The advantage is that it is easier to meet various design needs, eg: 2 frequency bands are requested to be very close, working frequency band needs to have a large Bandwidth, but the disadvantage is that it is easily interfered with by additional noise because both lowpass filter and highpass filter can only provide unilateral noise isolation performance, and noise can easily break through the protection and enter these 2 operating frequency bands.

Temwell 5G Diplexers Duplexers are Common to be Applied in:
  • Car receiver transmitter
  • The base station in the launch and accept
  • RF high power transmitter
  • Broadcasting equipment TV
  • Cable TV